- Fgtech v54 help how to#
- Fgtech v54 help 64 Bit#
- Fgtech v54 help driver#
- Fgtech v54 help upgrade#
- Fgtech v54 help windows 10#
OBD driver Fi-at MJ8DF K-line Read/Write, Checksum OBD driver Fi-at MJ8DF CAN Read/Write, Checksum OBD driver Fi-at ME17.31 CAN Read/Write, Checksum OBD driver Masrati ME9 CAN Read/Write, Checksum OBD driver Reault SID305 CAN Read/Write, Checksum OBD driver Pors-che SDI3 CAN Read/Write, ChecksumĬor-vette Utility CAN for change VIN, Code Align, Erase ErrorsĬorette Utility VPN for change VIN, Code Align, Erase Errors OBD driver Op-el Simtec75 CAN Read/Write, Checksum OBD driver Del-phi DCM3.5 for Ta-ta Sa-fari Read/Write, ChecksumĬhecksum recognition for DCM3.7 Ssan-gyongĬhecksum recognition for DCM3.7 Op-el and Sa-abĬhecksum recognition for DCM3.7 Ki-a and Hyu-ndaiĬhecksum recognition for Denso Sub-aru Tri-becaĬhecksum recognition for Denso Nis-san L200Ĭhecksum recognition for Denso Nis-san X-Trail
OBD drive Driver for writing Bo-sch EDC16C34/5 Citr-oen Ne-mo Read/Write, Checksum OBD driver Driver for writing Bo-sch EDC16C34/5 Peu-geot Bip-per Read/Write, Checksum
OBD driver Sim-os PCR2.1 VA-G 1.6 TDI Read/Write, Checksum Simos PCR2.1 VA-G 1.6 TDI Unlock Boot Tool - Read/Write EEPROM OBD driver for CRD 3.xx Merc-edes 2200 CDI Read/Write, Checksum OBD driver for Sim-os 10.xx VA-G 1.2 TSI Read/Write, Checksum OBD driver for Ma-zda 5, Ma-zda 6 2.0 Diesel ECU RF7x Read/Write, Checksum OBD driver for Ma-zda 5, Ma-zda 6 2.0 Diesel ECU RF8x Read/Write, Checksum OBD driver for Fi-at/Al-fa/Lan-cia Twi-nair/Mult-iair 8GMF and 8GSF Read/Write, Checksum OBD driver for Fer-rari 458 Italia MED9.6 Ecu Master and ECU Slave Read/Write, Checksum OBD driver SSang-yong Del-phy DCM3.7 Read/Write, Checksum
Fgtech v54 help 64 Bit#
I then did the FTDI update, and after reinstalling drivers, I was able to run the software on Windows 10, both 32 bit and 64 bit just fine.ĭid not go to the car yet and test, as I'm also waiting for Omron relays and ZVN and ZVP transistors, but I see no reason why it should not work.įinally some good info for 0475 EU version.įGTECH 0475 Added New vehicle and ecu type Than 0386 Version: I eventually ended up erasing the NXP flash with the Phillips tool, closing it, disconnecting the device, then opening Magic Flash and writing it back with that at 19200 without erasing first. I played with the settings and flashing procedure a few times, but that always kept failing following your steps and I thought I was left with a brick. Downloaded the Magic Flash tool, but neither that nor the Phillips tool would work to write after I erased the device (said it was CRP 2 or 3 when I checked initially then CRP disabled after the erase). That made it a bit difficult, as the software has VM protection, so I had to trick it into thinking it was not running on a VM, but that had to be switched off every time I wanted to copy new files to the VM.įound your posts everywhere when searching for 0386 to 0475 update, and since it looked like my board had all the right components (even the right ones on the most part), I got a PL2303 USB-TTL adapter (not genuine, as the latest driver would not work) and did the soldering.
Fgtech v54 help windows 10#
However, that only worked under my Windows 10 圆4 laptop, but not my Windows 7 tablet, which is 32 bit. Found it really annoying that the software for it would not run under Windows 10 so I had to create a VM to run either Windows 7 or Windows XP. Got a v54 China Galletto to play with on my car, and it was version 0386.
Fgtech v54 help upgrade#
Hi, can I upgrade V48 (0084-0103) to V54 0386 or 0475? Thanks!Īm I correct here in thinking, that if I have CRP2, then I can still safely write to it (and change it back later if I wanted), I just can not read the current info ? Password only by PM for active users with at least 20 posts after THANKS and REP Password request on forum will be ignored, you have been warned not to spam topic with it. If you want to check CRP level of your NXP mcu you can do that with FlashMagic and USB-TTL adapter. You need also a jumper in position to do that. Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset.
Fgtech v54 help how to#
FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 04ġ.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software.Ģ.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back.ģ.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish.
0 kommentar(er)
